Current is the rate of flow of electric charge. If this electric charge flows only in one direction, then the resultant current is called Direct Current (DC). The instrument, which is used to measure the Direct Current calledÂ **DC ammeter**.

If we place a resistor in parallel with the Permanent Magnet Moving Coil (PMMC) galvanometer, then the entire combination acts as DC ammeter. The parallel resistance, which is used in DC ammeter is also called shunt resistance or simply,Â **shunt**. The value of this resistance should be considered small in order to measure the DC current of large value.

TheÂ **circuit diagram**Â of DC ammeter is shown in below figure.

We have to place thisÂ **DC ammeter**Â in series with the branch of an electric circuit, where the DC current is to be measured. The voltage across the elements, which are connected in parallel is same. So, the voltage across shunt resistor,Â RshRshÂ and the voltage across galvanometer resistance,Â RmRmÂ is same, since those two elements are connected in parallel in above circuit.Â **Mathematically**, it can be written as

â‡’Rsh=ImRmIshâ‡’Rsh=ImRmIshÂ (Equation 1)

TheÂ **KCL equation**Â at node 1 is

**Substitute**Â the value ofÂ IshIshÂ in Equation 1.

Rsh=ImRmIâˆ’ImRsh=ImRmIâˆ’Im(Equation 2)

Take,Â ImImÂ as common in the denominator term, which is present in the right hand side of Equation 2

â‡’Rsh=RmIImâˆ’1â‡’Rsh=RmIImâˆ’1(Equation 3)

Where,

RshRshÂ is the shunt resistance

RmRmÂ is the internal resistance of galvanometer

IIÂ is the total Direct Current that is to be measured

ImImÂ is the full scale deflection current

The ratio of total Direct Current that is to be measured,Â IIÂ and the full scale deflection current of the galvanometer,Â ImImÂ is known asÂ **multiplying factor, m**. Mathematically, it can be represented as

m=IImm=IIm(Equation 4)

Rsh=Rmmâˆ’1Rsh=Rmmâˆ’1(Equation 5)

We can find theÂ **value of shunt resistance**Â by using either Equation 2 or Equation 5 based on the available data.

## Multi Range DC Ammeter

In previous section, we discussed about DC ammeter which is obtained by placing a resistor in parallel with the PMMC galvanometer. This DC ammeter can be used to measure aÂ **particular range**Â of Direct Currents.

If we want to use the DC ammeter for measuring the Direct Currents ofÂ **multiple ranges**, then we have to use multiple parallel resistors instead of single resistor and this entire combination of resistors is in parallel to the PMMC galvanometer. TheÂ **circuit diagram**Â of multi range DC ammeter is shown in below figure.

Place this multi range DC ammeter in series with the branch of an electric circuit, where the Direct Current of required range is to be measured. The desired range of currents is chosen by connecting the switch, s to the respective shunt resistor.

Let,Â m1,m2,m3m1,m2,m3Â andÂ m4m4Â are theÂ **multiplying factors**Â of DC ammeter when we consider the total Direct Currents to be measured as,Â I1,I2,I3I1,I2,I3Â andÂ I4I4Â respectively. Following are the formulae corresponding to each multiplying factor.

In above circuit, there are fourÂ **shunt resistors**,Â Rsh1,Rsh2,Rsh2Rsh1,Rsh2,Rsh2Â andÂ Rsh4Rsh4. Following are the formulae corresponding to these four resistors.

The above formulae will help us find the resistance values of each shunt resistor.